FUNDAMENTAL PLUMBING INSIGHTS FOR INSTALLING A BATHTUB

Fundamental Plumbing Insights for Installing a Bathtub

Fundamental Plumbing Insights for Installing a Bathtub

Blog Article

Call Today

Are you trying to locate additional info around How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a bath tub isn't exactly rocket science, yet it does need strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a new one is also a moderately tough task. If the old bathtub is easily easily accessible, the task can relocate immediately; if you need to open up a wall surface to eliminate the old tub as well as position the new tub, the task is much harder. In either instance, the task is within a house handyman's abilities, although you will need a helper to leave the old bathtub as well as set in the new one. Make certain you have actually qualified on your own for the work as well as are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed project, it is far better to consider employing one prior to you start. Chances are you may need a specialist plumber to make tube connections.
This article will help you set up a brand-new bathtub in your restroom if you have actually currently gotten a new tub as well as don't need to change the setup of your previous water pipelines.
Your tools and also material checklist ought to comprise the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Getting ready for the Installation


    Firstly, the sustaining framework supplied with the bath must be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the faucet includes a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
    Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you use all of the supplied washers.
    Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its last placement.

    Removing Old Taps


    If you require to replace old taps with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The process of removing the existing taps can be quite bothersome as a result of the limited gain access to that is often the case.
    Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the staying water that will originate from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
    Before carrying on to fit the new taps, contrast the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.

    Setting up the Bathtub


    Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are handy in uniformly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 little factors.
    The following objective is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the bath tub till the level checks out level.
    To mount taps, fit the bottom of the outermost versatile faucet connector to the ideal supply pipe by making a compression sign up with; then do the same for the various other tap.
    Activate the water system as well as check all joints as well as new pipework for leakages and tighten them if essential. Fill the tub and likewise check the overflow outlet and also the normal electrical outlet for leakages.
    Ultimately, take care of the bathroom paneling as described in the supplier's user's manual. Tiling as well as securing around the bathtub ought to wait up until the tub has actually been made use of at least once as this will certainly resolve it right into its last placement.

    Suitable New Touches


    If the tails of the brand-new faucets are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the current supply pipes.
    If you require to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washers remain in location in between the faucet and the sink. Safeguard the tap in position with the supplier offered backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former kind should be linked to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Tiling Around the Bath tub


    In the location where the bathroom fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to break a stiff seal, triggering the water to permeate the wall between the bath and also the tiling, resulting in difficulties with wetness as well as feasible leakages to the ceiling below.
    You can select from a range of coloured sealants to blend in your components as well as fittings. They are sold in tubes as well as cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked paper or soft rope. Keep in mind to always fill the bathtub with water before sealing, to permit the movement experienced when the tub remains in use. The sealer can break rather very early if you do not think about this activity prior to securing.
    Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the market. It is a good idea to fit the tiles utilizing waterproof or water resistant adhesive as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    I hope you liked our post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a ton for taking a few minutes to read through our posting. Enjoyed our content? Please share it. Let somebody else discover it. I praise you for your time. Visit again soon.


    Contact Us Today

    Report this page